What is a backflow prevention device?
A backflow prevention device is a valve on the water service that only lets water flow one way, from the main into the property. It stops used or contaminated water being drawn back into the drinking water main if the pressure in the street drops, for example when a main breaks.
It usually sits at the property boundary, near the water meter. Buildings with a fire hydrant or sprinkler service have a second device on that connection.

Which buildings need one tested?
It depends on the size of the water meter and the hazard rating of the site. A low hazard site on a 20 mm or 25 mm meter, which covers most houses, has a small device built into the meter that doesn't need testing. Sites rated medium or high hazard need a separate testable device, and so does any building with a fire hydrant or sprinkler service, which takes in a lot of unit blocks.
The rating has to be assessed on site by a plumber with backflow accreditation. If a site has never been assessed, Sydney Water treats it as high hazard.
The devices we test
- RPZD (reduced pressure zone device), used on high hazard sites
- DCV (double check valve), used on medium hazard drinking water connections
- DCDA (double check detector assembly), used on fire hydrant and sprinkler services
What Sydney Water asks of the owner
Sydney Water's rules put the job on the property owner. The device has to be the right one for the site, kept in working order, tested every year by a plumber with backflow accreditation, and the result sent to Sydney Water within 2 days of the test. Sydney Water keeps a register of testable devices and sends a reminder when the yearly test is due.
If a test is missed, Sydney Water can test the device and charge for it, restrict the water supply, or disconnect the property. The full rules are on Sydney Water's backflow page.
We're Sydney Water accredited for backflow testing. We test the device and lodge the result with Sydney Water ourselves, inside the 2 days, so there's nothing for the owners corporation to send in.
If a device fails its test
A device that fails can often be repaired with new seals, springs or check valves and tested again. If it's too far gone, or it's the wrong device for the site, we give you a fixed price to replace it before any work starts.
Water meter raises
In a lot of older buildings the meter and the device sit down in a pit, where they fill with dirt and water and can't be read or tested properly. We raise meters and devices above ground so they can be read, tested and serviced.
Common questions
How often does a backflow device need testing?
Every year. Sydney Water's rules say a testable device has to be tested every year by a plumber with backflow accreditation, and when it's first installed.
Who is responsible for the test in a strata building?
Sydney Water's rules put it on the property owner. In a unit block the device at the meter serves the whole building, so it's usually the owners corporation, and the strata manager sends us the work order.
We've had a reminder letter from Sydney Water. What do we do?
Send it to us with a work order, or call 02 9398 1397. We book the test and tell you if anything needs repair.
Do you send the result to Sydney Water?
Yes. We're Sydney Water accredited for backflow testing, and we lodge the result with Sydney Water ourselves within the 2 days their rules allow.
What happens if the test is missed?
Sydney Water can test the device and charge the owner, restrict the water supply or disconnect the property. It's much cheaper to book the test when the reminder arrives.
What's the difference between an RPZD, a DCV and a DCDA?
They suit different risks. An RPZD (reduced pressure zone device) is used on high hazard sites. A DCV (double check valve) is used on medium hazard drinking water connections. A DCDA (double check detector assembly) goes on fire hydrant and sprinkler services.
Can you raise a water meter out of a pit?
Yes. We raise meters and backflow devices above ground so they can be read, tested and serviced.
Where we do backflow testing work
Based in Randwick and working right across the Eastern Suburbs, including:
- Randwick
- Coogee
- Bondi
- Bondi Junction
- Rose Bay
- Woollahra
- Double Bay
- Vaucluse
- Maroubra
- Kingsford
- Kensington
- Bronte
- Clovelly
- Paddington
- Darlinghurst
- All areas
Last updated . McElroy Plumbing, Randwick.

